Nitrous Oxide Nitrous Express | NOS | Cold Fusion Nitrous

2005 Mustang GT w/ NX 125 shot

Thread Tools
 
Search this Thread
 
Old 04-19-2006, 10:21 PM
  #11  
Launching!
 
K Bo's Avatar
 
Join Date: Dec 2005
Location: Houston, TX
Posts: 252
Default

Originally Posted by cleveland
I will keep ya updated.

I only run the nitrous at the track and that isnt too often for me so maybe the tranny can still live a long life with more than 600ft/lbs flowing through it.

-Dan
My problem is I would want to spray all the time.

As far as tuning, are you just re-programming between N/A to nitrous tunes or do you have a flip chip of some sort? That is also a concern of mine. I don't want to re-program every time I want to spray.
K Bo is offline  
Old 04-20-2006, 12:11 AM
  #12  
Teching In
Thread Starter
 
cleveland's Avatar
 
Join Date: Mar 2006
Posts: 42
Default

Im not running a separate tune so Im good to go at any time, granted I have 104 octane in the tank. The knock sensor sensitivity was turned up and programed to act much like a stand-alone timing retard box, its set to retard so many degrees immediately as any pre-ignition is detected. Its interesting and worked well on those 125 shot dyno runs.

-Dan
cleveland is offline  
Old 04-20-2006, 03:51 AM
  #13  
Launching!
 
K Bo's Avatar
 
Join Date: Dec 2005
Location: Houston, TX
Posts: 252
Default

Originally Posted by cleveland
Im not running a separate tune so Im good to go at any time, granted I have 104 octane in the tank. The knock sensor sensitivity was turned up and programed to act much like a stand-alone timing retard box, its set to retard so many degrees immediately as any pre-ignition is detected. Its interesting and worked well on those 125 shot dyno runs.

-Dan
So you just run one single tune N/A and on nitrous? How does it run on this tune when not spraying?
K Bo is offline  
Old 04-20-2006, 03:58 AM
  #14  
Teching In
 
jumpinjoe's Avatar
 
Join Date: Dec 2005
Location: Kerman, CA
Posts: 14
Default

Originally Posted by cleveland
My next possible track day is the 30th of this month. Im going to start getting my 275/50-17 M&H Racemaster drag radials preped tomorrow.

-Dan
Sacramento Raceway?
jumpinjoe is offline  
Old 04-20-2006, 01:52 PM
  #15  
Mustang Moderator
 
ITSTOCK's Avatar
 
Join Date: Feb 2004
Location: Horsham, PA
Posts: 516
Default

THAT is a clean install! Very nice looking.
ITSTOCK is offline  
Old 04-21-2006, 03:04 AM
  #16  
Teching In
Thread Starter
 
cleveland's Avatar
 
Join Date: Mar 2006
Posts: 42
Default

Like I posted earlier, the only thing that was added to the maximized NA tune was the increased sensitivity of the knock sensors. If no knock is sensed while I jet around town without the nitrous and Im using 91 Octane, everything is fine. I could spray the nitrous while using just 91 octane fuel but I'd probably kill the set of spark plugs again. The tune was written to remove so many degrees of timing upon nitrous/pre-ignition and not cause any issues.

Im waiting on the exact words from the tuner on what he did with the "retard box" parameter within the tune. I can understand what he did but I may not be using the best of words to properly describe it. I also have to make sure the tune has all the kinks out of it within the next week; shifts points and rev limits are the most important and so far those two points still need to be addressed.

I have been really driving hard around town the last few days since putting the Drag Radials on, its nice not spinning with my foot into it a bit more. Of course this is useful for my datalogging so I can confirm everything is proper. The last thing I want to do is bounce off a rev limiter with a .057 or .062 nitrous jet still spraying.

-Dan
cleveland is offline  
Old 04-23-2006, 05:43 PM
  #17  
Mustang Moderator
 
LS1 KLR's Avatar
 
Join Date: Mar 2002
Location: Katy, Texas
Posts: 358
Default

Nice plumb job and clean wiring! I like it.

Who makes those fuel rails??
LS1 KLR is offline  
Old 04-23-2006, 08:30 PM
  #18  
Teching In
Thread Starter
 
cleveland's Avatar
 
Join Date: Mar 2006
Posts: 42
Default

Those rails are by CPR Racing.

-Dan
cleveland is offline  
Old 05-04-2006, 05:47 PM
  #19  
TECH Fanatic
 
Gold Z's Avatar
 
Join Date: Nov 2001
Location: Wichita Falls,TX
Posts: 1,033
Default

Very clean install. Nice numbers too. Why are two nitrous lines going through your hood? Pressure gauge on the hood?
Gold Z is offline  
Old 05-05-2006, 10:29 PM
  #20  
Teching In
Thread Starter
 
cleveland's Avatar
 
Join Date: Mar 2006
Posts: 42
Default

Yes, pressure gauges on the hood but soon to be relocated once the 4" Cowl hood arrives next week.

-Dan
cleveland is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
donkeypunch
Nitrous Oxide
12
12-13-2009 02:50 AM
HOTRODKEV
Appearance & Detailing
2
10-17-2007 04:41 PM
Nino
Sponsor Specials & Group Purchases
0
11-03-2006 02:24 PM
JustAnIlluzion
For Sale
0
09-10-2006 02:49 PM
Speeds8erM-1
Multimedia Exchange
0
04-02-2006 04:39 AM



Quick Reply: 2005 Mustang GT w/ NX 125 shot



All times are GMT -5. The time now is 03:41 AM.